As a source of thermal energy for the loggia, various heating systems are used, mounted mainly in the floor. They allow you to maintain optimal temperature conditions, to form the most favorable conditions.
There are several options for installing underfloor heating. To make the right choice, it is necessary to compare the pros and cons of each decision.
We will tell you which warm floor on the balcony is preferable in a particular situation, and also give step-by-step instructions for installing the heating system.
Loggia heating systems
There are several types of floor heating systems that are used to warm the balcony and loggia.
All devices are related to electric underfloor heating:
- heating mats;
- two-core heating cables;
- infrared shielded film.
Consider the system in more detail.
Image Gallery
Photo from
Glazed loggia sitting area
Winter garden room
Organization of a nursery on a furnished loggia
Lounge in an office building
Underfloor heating during redevelopment
Year-round use of premises
Warm floor instead of radiators
A place for work and privacy
Heating mats and their types
One of the most popular and budget systems are heating mats. By themselves, they represent a single heating cable, wave-wise attached to a special mesh of durable fiberglass. Devices belong to the class of systems with cable heating, their installation is carried out exclusively in the floor.
Heating mats can have a length of 50 cm to 3 meters; the width of the cable holding reinforcing mesh is usually 50 cm
A single or two-wire cable acts as a heat source. Its diameter varies in the range of 2.5-4.5 mm. For the operation of the mats, a power source of 220-230 watts is required.
The cable is protected by a special plastic screen. The length of the cold wire usually exceeds 2 m.
Industrial mats are divided into two groups.
They are divided by type of cable into:
- single core;
- two-core;
Single core systems. Their feature is that they must be laid so that the two ends are connected to the thermostat. This greatly complicates the installation, since cutting mats is required.
Also, a mat with a single-core cable emits an electromagnetic field, so it is not introduced into rooms where people are constantly located.
The main advantage of single-core heating equipment is its low price, the possibility of implementation in the bathroom, toilet, kitchen
Two-core mat - Advanced single core modification. Here, in addition to the heating core, there is an electric cable. Its implementation in the design allows one end to be connected to the thermostat, and the other can be hidden in the coupling, which makes it possible to finish the installation anywhere.
A two-core mat practically does not emit an electromagnetic field, therefore it is completely safe for humans. It can be introduced not only into the floor of the balcony, but also in any other room as a source of additional heat.
Heating mats also differ in power, can generate from 60 to 2300 watts of energy. About how to calculate the required mat power, you can read below.
Both single-core and two-core mats are reliable, able to serve impeccably for many years. Usually single-core modifications are thinner than two-core ones, have a greater power, therefore they are able to heat the floor surface faster.
Pros and cons of heating mats
Consider the features, advantages and disadvantages of heating mats.
- When using mats, the height of the room decreases by only a couple of centimeters, taking into account the height of the tile and the layer of glue.
- The system is economical, rationally consumes electricity. If there is furniture on the balcony, then the mats do not fit under it.
- Heating mats are easy to install. The only thing that can cause complexity is the connection of the system to the thermostat.
- Use mats for heating for a short time. They are not designed for permanent round-the-clock work.
Tile adhesive can be applied on top of the mats and the tile itself can be laid. The choice of the device takes into account the area of the heating surface, the heat loss of the loggia. For mounting on a balcony, it is undesirable to take a long mat, since the device cannot be shortened.
Only the cold ends will be reduced, so for the balcony you need to choose a device that is most suitable for the floor area.
Image Gallery
Photo from
Loggia underfloor heating components
Fully prepared for installation system
Laying floor tiles on heating mats
Electromats in non-standard rooms
Installation of heating mats
Installation of heating mats must be carried out with caution. It is important to protect the cable from mechanical damage. It is unacceptable to use cutting and sharp objects during installation, leave them unattended.
It is also important to try not to step on the cable. In order to eliminate the likelihood of this incident, it is advisable to install in shoes with soft soles or without shoes, and before installation, completely clean the floor surface from contamination.
Caution should be exercised during fixing the tiles, applying glue and cleaning the seams. During these operations, the cable may be accidentally damaged.
The device of the floor heating system using heating mats includes a number of traditional steps:
Image Gallery
Photo from
Stage 1: Laying the heating mats on a level base
Stage 2: Open floor heating systems
Stage 3: Putting tile adhesive on the warm floor
Step 4: Laying floor tiles on the warm floor
Consider options for laying mats on different types of surfaces.
On the concrete floor of the loggia, first insulating material is installed, then the floor is leveled, a shock absorber is installed, which will prevent deformation when heated. Then a mat is placed on the shock absorber, after which it is covered with tiled glue, on which tiles are laid.
At the last stage, the protective tube for the temperature sensor, thermostat is installed, cold wires are connected.
Before laying the mat, to ensure its maximum efficiency, it is possible to lay a layer of thermal insulation on the floor (+)
If the floor is laid out of wood on the balcony, then the surface is first leveled with a concrete layer of 7-9 mm, then the heating mats are laid, solid foam is laid, and then the floor is covered with wood.
If the installation is done on an old tile floor, then a concrete screed is made, a heating element is installed, it is covered with tile adhesive, and then a new tile coating is created. If the floor tiles were in good condition, then the leveling screed can not be done.
Heating mats can be easily installed on the old tiled floor of the loggia without dismantling it (+)
Consider the features of installation in more detail.
Before introducing mats into the surface of the floor, a schematic installation plan should be made.
The project should display:
- contour of a heated surface;
- styling scheme;
- location of the temperature sensor, temperature controller, taking into account the location of the power wiring.
It is important to prepare the surface for laying mats before starting work. For this, cracks are putty on the floor. After it dries, the floor is cleaned of dust and dirt. If the surface is wooden, make sure that it is firmly fixed.
Before laying, you need to install the groove for the tube that comes with the temperature sensor. It is important that it is located at the top edge of the product at the same distance from the heating cables.
During work, you need to glue the tube on one side with electrical tape so that tile glue does not get into it. The second end is connected to the thermostat itself, which is located in the junction box.
Laying can be done in two ways - cable up or cable down. The first method is the simplest; it is most often used in practice.
The way in which laying is done with the cable up is that the mats are laid down with a net. Further, using glue, the device is pointwise attached to the floor surface.
After - tile adhesive of the required thickness (usually 3-5 mm) is applied to the surface of the mat, after which they start laying the tiles.
It is important to distribute the adhesive evenly over the surface of the mat to avoid the formation of air voids, since during operation they can lead to overheating of the cable and its breakdown
The cable must be completely immersed in a heat-conducting medium (tile adhesive, etc.).
The method in which the cable is laid with the cable down (i.e., the net up) is more complicated in execution. Before laying tiles, a mat pattern is made. To do this, it is spread so that it completely covers the heated surface.
Next, cut the mat grid, then roll it up. A 2-3 mm layer of glue is applied to the floor, after which the mat is unwrapped with the cable down and slightly pressed.
During installation, it is important to ensure that the distance between the cables is not less than 5 cm. A second layer of adhesive of 5-6 mm is applied with a notched trowel directly on the heating mat, after which the tile is laid.
Heating electric cable
At the heart of any warm floor system is a heating electric cable. It acts as the main heating element. The control is carried out using electronic temperature controllers of various modifications.
For the functioning of the device, a voltage of 220 V.
Image Gallery
Photo from
Cable floor heating on the loggia
Variation in cable laying pitch
Fixing the cable to the reinforcing mesh before pouring the screed
Sophisticated stacking scheme for the heating coil
The cable system includes a cable heating section, its main element is a two-core shielded cable, which is connected on one side by a supply conductor protected by a sleeve, and on the other, by a heating core.
The specific heat dissipation of the cable is approximately 18 W / m.
The cable is laid in a concrete screed or tile adhesive. The product is able to provide floor temperature from +25 to +32 degrees
The advantages of the cable are as follows:
- the electromagnetic field created by the device is cavity safe for humans;
- due to the use of low power in the heating core design, the cable durability and its service life are increased;
- ease of installation;
- shielding film provides electrical, fire safety of the product, protects it from mechanical damage.
Installation on a concrete floor has a number of features. It is advisable to insulate with extruded polystyrene foam with a thickness of 20-30 mm or any other heat-insulating material.
Next, you need to cover the insulation with a concrete screed of 10-15 mm. This will eliminate the contact of the insulation with the floor heating element, otherwise the device may overheat.
After the procedure, the mounting tape is laid and fixed on the floor. The cable is laid evenly undulating throughout the area. It is important that its nodes do not intersect. The bending radius must be equal to or more than 10 times the diameter of the cable. Fix the device with a mounting tape, securing it protruding parts.
In one thermostat, it is possible to connect from two or more heating cables. The cold end is installed in a box in a gate located in the wall. Sensors are mounted between the cable strips and output to the installation box. It is supplied with 220 V power from the nearest outlet (+)
After laying, check the compliance of the real resistance of the heating core with the information in the passport. You can connect the cable before installation to check its operability, and then carry out laying and screed.
Couplings should be located in concrete screed. Before the device, the couplers make up the cable laying scheme, where they determine the places for the location of the couplers.
It is important to remember that the cement screed finally hardens after 28-30 days. Until this time, you can not turn on the system. It is also forbidden to start sections of the heating cable that are in a folded position. The laying step should be calculated according to the passport.
In detail, with the stages of laying the heating cable on the loggia floor, a brief photo-instruction will introduce you:
Image Gallery
Photo from
Before laying the cable heating system, we repair the base. If necessary, embroider cracks and fill them with a solution
In the place chosen for the installation of the thermostat, we will wall the wall for installing the cable in it in the corrugated plastic channel. In the floor we form gates for laying sensors connected to the control unit
On the repaired floor we lay a foil waterproofing, which at the same time will prevent heat leakage into the floor
The loggia shown in the example is made in the form of G. Where the trimmed panels connect, we glue the lines of connection with tape
On the substrate we have mounting metal strips that will fix the cable. We fix them to the floor, then we loop the cables in 10 cm increments
We install the thermostat, connect to it a system, temperature sensors buried in the gates on the floor. Checking the performance of the assembled system
Disconnect the system from power. We install beacons from a metal profile and arrange a semi-dry screed
We put waterproofing on top of the cable floor in the screed, then laminate, do not forget to fill the furrow with the cable for the gypsum solution control unit
Step 1: Repair the loggia floor before laying the heating cable
Step 2: Strobing walls and floors under the thermostat cable
Step 3: laying foil insulation on the floor
Step 4: Adhesive Tape Adhesive
Step 5: Laying the heating cable on the substrate
Step 6: Connecting the heating system to the control unit
Step 7: Device for screed heating floor
Laying flooring over underfloor heating
Infrared heating film
The principle of operation of the IR film is based on the generation of long-wave infrared rays. The device itself has the form of a canvas coated on both sides with a polyester film. It is flexible, making it easy to install on any part of the floor.
For implementation, pouring a cement screed or an adhesive base is not required, the film can be easily installed and dismantled.
The film layers consist of carbon and copper tires, due to which heat transfer of 100% is achieved. IR film works efficiently at low temperatures, is widely used for installation in the floor of the loggia
The film is a kind of emitter of infrared rays, which a person interprets as heat. Its maximum heating temperature is 50 ° C.
Any IR film consists of:
- heating carbon element, which is a converter of electricity into heat;
- bimetal tiresby means of which energy is supplied to the heating elements;
- bilayer polymer filmperforming the functions of protection against mechanical damage.
The device works from an electric network of 220-230 V.
You can fix the film to the floor using a stapler, adhesive base or any other method, depending on the type of coating that will be installed (+)
The current passing through the components of the system is converted into thermal energy, it is transferred to the environment, which then heats the air mass around it.
Types of infrared films
There is a wide variety of IR films that differ in specific technical parameters and appearance. Two main types can be distinguished - low and high temperature models. The films also differ in power, limiting heating temperature, thickness, width, and areas of application.
Installation of a continuous carbon film, used as the main heating system of the equipped loggia, is quite simple:
Image Gallery
Photo from
Step 1: Screed under the film floor
Step 2: Installing the underfloor underlay
Step 3: Laying carbon fiber heating panels
Step 4: Insulating the Free Edge of the Carbon Film
Step 5: Assembling the Electric Heating System
Step 6: Pasting the joints with bitumen tape
Step 7: Fixing the carbon sheets with tape
Step 8: Laying Finish Flooring
When choosing a film, the key parameter is the temperature of its heating. So, if it exceeds + 27 ° C, then the laminated coating should be discarded, since it is irreversibly deformed when exposed to high temperature.
Therefore, high-temperature modifications should be laid under ceramic tiles.
If the floor covering will be a parquet board, laminated flooring, carpet, etc., then you need to install a low-temperature system, heating up to + 27 ° С. For coating in the form of tiles, expanded clay, you can install high-temperature modifications, generating + 45- + 50 ° С
In the loggia, you can install a warm infrared film both on the floor and on the walls and ceiling. Additionally, the panels are mounted on both walls under the windows, opposite the windows. This heating method is called - heating system PLEN.
When choosing an IR film, it is important to focus on the area of its application.
Significant benefits of IR film
Experts highlight a number of advantages of IR film.
Among the main advantages include:
- environmental Safety - radiation is considered beneficial for health;
- maintaining air quality - during the operation of the device, it is not air that is heated, but interior items, therefore, oxygen does not evaporate, the composition of the air does not change;
- lack of radiation electromagnetic type;
- ease of installation, extensive customization options.
IR film is durable, practically does not fail, and does not require repair.
Infrared film systems are excellent outdoors. They are actively used in the arrangement of balconies and loggias. A significant advantage of IR floors is that this is the only option that allows you to effectively heat rooms without glazing.
The process of creating an IR system on the balcony floor will be presented by the following gallery:
Image Gallery
Photo from
Stage 1: Laying Insulation
Stage 2: Location of heating film panels
Stage 3: Coating over IR floor
Stage 4: Connecting the heating system to the control unit
If you plan to choose an IR film for the balcony, we suggest that you familiarize yourself with the information on installing and connecting such a warm floor:
- Infrared carbon warm floor: operating principle and laying rules
- How to make an infrared warm floor with your own hands: installation and connection of a film floor
Mounting the temperature sensor
To provide the necessary microclimate in the room, use temperature controllers equipped with a temperature sensor. They effectively interact with cable systems, IR film.
The functions of the thermostat include maintaining the set temperature, adjusting it, optimizing power consumption. Depending on the modification, the functions of the device may be varied.
The principle of connecting the thermostat is the same for any system. We will consider the features of installing a temperature sensor for heating mats.
One thermostat is able to regulate the temperature of several heating mats simultaneously. Connect cable systems in parallel, the maximum current should not exceed 16 A, which corresponds to 3600 W at 230 V
If the total power of the mats is greater, then additional equipment is required for the installation of the thermostat in the form of an input circuit breaker, an RCD, a power relay, a circuit breaker in the directions, a special temperature regulator.
To install the controller, you must perform the work in the following order:
- create a special hole in the wall for mounting the box;
- drill a recess in the wall to install the power wire and create a hole for laying the connecting channel;
- install, configure according to the instructions;
- place the sensors in a corrugated plastic tube with a diameter of 16-20 mm.
The tube must be tightly closed at one end to protect the wires from getting into solutions, water. From the opposite end, the tube is placed in an installed box.
The regulator is recommended to be located near the wiring, in order to save on supply wiring, it is desirable to install it on the wall in the living room in the most convenient place
The permissible bending radius of the wiring is at least 5 cm. The tube with sensors is fixed to the floor. She must go between the loops at a distance of at least 20 cm.
It is important to remember that during installation it is impossible to shorten the heating cable, replace the supply wires, make adjustments to the design of the thermostat, carry out repair and installation work with the power supply turned on.
Principle of calculation of floor systems
Before choosing any floor system, it is important to calculate the power of the heater, determine its required length.
To do this, you need to calculate the heat loss of the loggia. A lot of thermal energy goes out through the window openings, so it is quite problematic to ensure a temperature of + 20- + 23 ° C, especially in the winter season. Therefore, it is recommended to install heating equipment in heating mode.
You can calculate the heat loss of a balcony using the online calculator.
Before installing the underfloor heating system on the loggia, it is important to pre-warm the room
Recommended temperature of heating mats, cable or IR film is + 26 ° С. This mode is suitable for insulating parquet floors. If a tile, marble or other heat-conducting coating is used as a coating, the recommended cable temperature is + 28- + 31 ° С.
Typically, loggias need 160-180 watts per meter2 for heating and 200-220 watts per m2 for heating mode. Given these recommendations, you can calculate the required cable length, installation step, system power.
For example, a loggia has an area of 2 m2. The flooring is a tile, screed is not planned. Take the heating mode, which requires 200 watts per m2. Next, we determine the heating area.
It is calculated by the formula:
Sgr= Stotal-Setc, Where
- Setc - the area occupied by cabinets and other furniture;
- Stotal - the total area of the room.
Let's say the area occupied by furniture is 0.5 m2. Then Sgr= 2-0.5 = 1.5. For the loggia, the heating mode is selected, so the required cable power is 200 W per m2.
Then the recommended power of the system is 1.5 * 200 = 300 W per m2.
If the screed is not planned, choose a thin cable system that can completely fit into the layer of tile adhesive.
You can select a system with the required characteristics from the tables describing the characteristics of the equipment.
Using the technical characteristics of the mats, you can determine the optimal model based on individual requirements (+)
Based on the table, we determine the mat power, its dimensions and length by area. In our example, the mat power is 0.25 kW, and the length is 17 m.
Next, we look for the installation step. We calculate it by the formula:
h = (Sgr* 100) / Lcabwhere
- h - laying step;
- Lcab - cable length in meters.
We substitute the values in the formula, and we get: h = 1.5 * 100 17 = 8.8 cm.
When laying mats or cables, remember that the distance from the walls should be 10 cm.
The video tells about the features, general principles for installing heating mats:
From the video you can learn about the features of installing and connecting the thermostat:
You can learn about installing IR film from the video below:
Cable systems, IR film are of high quality, low cost, practicality and durability. You can install them yourself without the involvement of specialists.
It is only important to choose the right equipment, taking into account the area of the heated surface, the type of coating and other factors.
Anyone interested in the matter of heating the balcony and using a warm floor to heat the loggia, we suggest leaving comments and asking questions. The contact form is located in the lower block.