Have you noticed how many different methods experienced craftsmen can offer to solve the same problem? The installation of the gas pipeline is no exception. So, the connection of gas pipes by professional gas specialists is performed using different materials and techniques. In the arsenal of masters, carving and welding, soldering and flanges. They actively use proven techniques for decades and recently appeared techniques.
Knowing the basic methods, understanding the tools and modern materials, it is easier to track the correctness of the work, to control the actions of the invited specialists.
In this article, we described the main options for fastening gas pipes, methods of sealing joints. After reading it, you will understand the types of pipes, features of materials, technologies for working with them. We paid special attention to methods for checking already completed connections, since the operation safety of domestic gas equipment depends on their correctness.
Features of connecting gas pipes
For a long time, the gas pipeline consisted exclusively of metal pipes of different diameters. The material was appreciated for the possibility of creating a seamless line capable of maintaining absolute tightness under high pressure.
The joints of rusted metal pipes are a source of increased danger, since it is at the joints that the steel alloy is destroyed especially quickly
The search for other options was made by a significant drawback of the metal alloy - under the influence of moisture, after several years of operation, it began to rust, jeopardizing the integrity of the pipeline.
Then pipes from other materials began to appear:
- Copper, the advantage of which is corrosion resistance, the negative is the ability to maintain integrity at low pressure not exceeding 5 kPa.
- Mild steelnot affected by rust. Its disadvantage is the difficulty in processing and high cost. Therefore, PVC pipes with a steel outer braid are used to equip gas pipelines.
- Polyethylene. Flexible and lightweight, this material does not conduct electricity, is cheaper than other analogues and can withstand strong transformations without loss of integrity.
More information about the different types of gas pipes and the features of their choice can be found in this material.
Elements connecting the highway and the layering leading to the consumer began to be made of rubber. For such compounds, heat-resistant rubber is selected that is not prone to drying out with excessive insolation.
When installing rubber compounds, finished factory products are used. Flexible eyeliners made in artisanal conditions do not comply with TB regulations
The choice of material is determined by the pressure in the gas pipeline, the required throughput and is calculated by specialists.
The same goes for connections. Only a professional can determine the appropriate type of fastening, correctly correlate it with the pipe material, technical operating conditions.
Gas pipe connection options
Today, masters distinguish 5 types of connections when installing a gas pipeline. This is welding used for metal pipes, soldering used for copper and PVC, inset, threaded and flange connections.
Option number 1 - weld
Steel pipes are treated using an inverter apparatus or gas welding equipment. The ends to be connected are located at a distance of 1.5-2 mm from each other, thoroughly fixed.
In the process of metal melting, the welder makes two seams: the main and the additional one.
Experienced craftsmen cool the heated metal and only then get rid of the scale. This makes it possible to avoid cracking.
The polyethylene elements are joined by a device that controls the temperature reached by heating. For the connection, a fitting with a melting element is used. By heating the surrounding material, it turns the mixture into a homogeneous mass. The result is a sealed, durable seam.
Option number 2 - soldering pipes
Butt brazing is suitable for both metal pipes and thermoplastic polymer products. The work is carried out on a modular unit, including a hydraulic unit, a centralizer, a soldering iron and an integrated torch.
The algorithm is as follows:
- The ends of the elements to be welded are cleaned of chips, dust, foreign particles. Degreased.
- Using a soldering iron for polypropylene pipes, the parts are heated and come together until an influx of 1 mm thick appears on the junction surface.
At the end of work, the connection is left in the unit until it cools completely. Any movement during a decrease in temperature can cause fistulas.
Option number 3 - insert into the pipe
The box is a method that requires special qualifications. It can be performed in the hot way, in which the arc welding unit is used, and cold, when the drilling equipment is the main tool.
The meaning of manipulation is to organize a tight branch from the whole pipe.
Some owners of private houses, when connected to the central highway, carry out cold insertion on their own, without notifying neighbors, the supplier company. Doing this is prohibited. Only licensed organizations can connect a new section to gas
The insert by the first method is permissible only when the pressure in the gas pipeline is reduced to a value of 40-50 kg per square meter. see. The second can be implemented without lowering the pressure. In both cases, permission of the supervisor is required.
Read more about how to crash into a gas pipeline.
Option number 4 - the use of threaded connections
Threaded connections are used throughout the gas pipeline: from end elements to different types of branches. If flexible rubber eyeliners are already equipped with appropriate nozzles, then metal pipes often have to be cut.
It is performed in the following way: the surface of the future thread is cleaned, filed, lubricated with machine oil. Then, with the help of a pipe hob, cutting is performed.
If it is supposed to join two fixed sections of the gas pipeline, the gas pipes are connected by means of a coupling. This is a separate metal element with internal thread. The imposition of it on the external thread of the pipe ends makes it possible to ensure a tight fit.
Experienced craftsmen always monitor the position of the screwdriver: it must be located in relation to the pipe strictly perpendicular. In addition, they perform slicing with the alternation of a full turn forward and half back. This is done to get rid of chips that prevent a smooth cut.
Even perfectly crafted threads do not provide perfect joint integrity. Therefore, additional materials are always used to seal gas threaded connections.
Option No. 5 - flange connections
This method is suitable for pipes made of copper, steel, polyethylene. Used only in low pressure areas.
A flange is a flat part with holes made in it. The part itself serves as a connecting element. The holes in it are for studs and bolts.
It is necessary to select a flange taking into account the parameters prescribed in GOST 12820-80. The document takes into account the correspondence of the nominal pressure of the gas pipeline and the size of the part
For PVC pipes, special fittings are used that are connected by welding. In the case of metal elements, you can do without heating. They use bolts to fix the flanges.
Joint sealing materials
Threaded and flanged joints require additional sealing.
The choice of material for the gasket is based on the fact that it should:
- to withstand the loads stipulated by the project, including pressure drops;
- to level defects of the condensed surface;
- fill the space between connected elements.
That is, the gasket must be flexible, strong and dense. The most famous material that meets these requirements is flax. Linen strand is actively used to seal joints of gas and water pipes.
More modern materials - pastes, threads, sealants, FUM tape are used a little less often: due to the higher cost and some conservatism of experienced specialists.
Pros and cons of linen ribbon
Linen tape is wound tightly on the thread, creating a dense layer. The advantages of the method are low cost, high adhesion, strength of the fixed joint.
Previously, flax fiber was used with lead red miner impregnated with drying oil. Nowadays, special sealing pastes are increasingly being used
Cons - the destruction of flax over time, the complexity of dismantling, high requirements for the experience of a specialist.
If the gas pipe connection on the laid flax thread is made with too much force, the gasket may break. Such a joint will not be airtight. Therefore, it is better if the manipulation is entrusted to an experienced master.
Pastes based on oils and resins
Oil and resin compositions do not harden. The substance applied to the joint remains viscous for a long time, effectively resists the penetration of gas into the external environment.
With a small gap, an experienced specialist will choose another method, since non-hardening paste will be effective only on long threads
A big plus is the easy application, which even a beginner locksmith can cope with. Cons - lack of fixed fixation, low resistance to pressure.
With increasing pressure in the gas pipeline, the paste is gradually squeezed out of the compound.
Drying Sealants
The basis of these compounds are solvents. After application, the substance dries, provides a firm hold. It can be used separately or in pair with linen winding for gas connections.
Knowing that the threaded connection is sealed with a drying sealant, it is worth checking it periodically, tighten with a wrench. This applies to all types of pipes.
Experts attribute the strengths of drying sealing pastes to the strength of the resulting compounds. In addition, the composition is easy to apply: during processing, it acts as a lubricant, and begins to dry, already in the threaded gap. Of the shortcomings, a tendency to shrink is distinguished.
Anaerobic adhesives
Viscous, polymerizable, non-shrink adhesive is the best sealant for threaded and flanged gas connections. Filling the space at the joints, it freezes only there, remaining fluid and viscous from the outside.
Excess glue can be easily removed from the surface, and the dose that gets inside will remain in place and quickly polymerize.
For ease of installation, manufacturers offer adhesives with different drying times. It varies from 3 minutes to several hours. This should be considered when choosing a composition.
The only drawback of anaerobic adhesive is the inability to use it at low temperatures. With a strong minus, the polymerization time sharply increases. And in some situations, it may not come at all.
Nylon thread
The principle of using nylon thread is similar to the method of using flax fiber: the material is wound on the external thread of one element, and then pressed against the internal thread of another.
Benefits include:
- low cost;
- wide temperature range, the upper limit of which is fixed at around 130 degrees;
- possibility of use in conditions of high humidity;
- reliability of the processed compound.
Among the shortcomings, the need to roughen the thread is highlighted - it is extremely difficult to hold the material on smooth metal. In addition, the nylon thread is not suitable for sealing pipe joints with a diameter of more than 80 mm.
Teflon tape
FUM tape is a relatively new type of sealant, but quite popular. Its main advantages are elasticity, chemical resistance and heat resistance.
The tape is easy to wind, it has a long service life, suitable for metal and polyethylene pipes.
It is important to apply the FUM tape correctly: on a previously degreased surface, observing the direction of the thread. If the check shows a gas leak through the processed joint, then for the correction it is necessary to completely remove the old winding
However, there are also disadvantages. This is a low level of sealing compounds of large diameters and sensitivity to bumps - roughness, nicks, metal chips can easily violate the integrity of the tape.
Methods for checking the tightness of joints
The tightness of the gas pipeline is checked by sections. In the situation with apartment buildings, a segment is selected from the place where the fuel is introduced into the building to the taps of household equipment.
Stubs are placed at the ends of the plot. In the pipes, pressure is increased, exceeding the standard indicators by 25%. A drop in pressure is the reason for checking the connections.
It is forbidden to check a gas leak with an open fire: by means of matches, candles. Lighters and piezo lighters are not suitable for this purpose. Fuel accumulated near the connection may explode
The integrity of the joints, branches and connection points of equipment is checked in two ways:
- Using a gas leak indicator.
- By applying a soap solution, emulsion.
In the first case, a digital, sound or color signal of the device will notify about the danger. In the second, it is necessary to monitor the appearance of bubbles. Their presence indicates a violation of the integrity of the connection.
Three methods of sealing standard threaded connections are shown in the video:
Having got an idea about the materials from which pipes for a gas pipeline are made, types of joints and sealing methods, it becomes clear that it is better to entrust all the work to professionals. An experienced master will be able to choose the best joining method, a suitable sealant, and correctly check the integrity of the connection.
If you have experience in sealing compounds, you are in the know about the novelties in the market of sealing compounds, write. Both novices and those who have something to share visit our site. Share experience, knowledge, ask questions. The form below allows you to accompany the comment with photos, diagrams, drafts.